{"id":131,"date":"2024-07-12T06:23:18","date_gmt":"2024-07-12T06:23:18","guid":{"rendered":"https:\/\/www.loyal.sg\/blog\/tolerance-symbols-2.html"},"modified":"2024-07-15T07:18:30","modified_gmt":"2024-07-15T07:18:30","slug":"tolerance-symbols-2","status":"publish","type":"post","link":"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html","title":{"rendered":"Tolerance symbols"},"content":{"rendered":"\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Tolerance
\n
\nsymbol<\/strong><\/td>\n		Definition<\/strong><\/td>\n<\/tr>\n
<\/td>\nRadial bearings inner ring – cylindrical and tapered bore<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
d<\/strong><\/td>\n\n
    \n
  1. Cylindrical bore: Nominal bore diameter<\/span><\/li>\n
  2. Tapered bore: Nominal bore diameter at the theoretical small end<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
\u0394dmp<\/strong><\/td>\n\n
    \n
  1. Cylindrical bore: Deviation of a mid-range size (out of two-point sizes) of bore diameter in any cross section from its nominal size<\/span><\/li>\n
  2. Tapered bore: Deviation of a mid-range size (out of two-point sizes) of bore diameter at the theoretical small end from its nominal size<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
\u0394ds<\/strong><\/td>\nDeviation of a two-point size of bore diameter of a cylindrical bore from its nominal size<\/td>\n<\/tr>\n
Vdsp<\/strong><\/td>\nRange of two-point sizes of bore diameter in any cross section of a cylindrical or tapered bore<\/td>\n<\/tr>\n
Vdmp<\/strong><\/td>\nRange of mid-range sizes (out of two-point sizes) of bore diameter obtained from any cross section of a cylindrical bore<\/td>\n<\/tr>\n
B<\/strong><\/td>\nNominal inner ring width<\/td>\n<\/tr>\n
\n\u0394Bs<\/strong>
\nNormal,
\n
\nModified1)<\/sup>\n<\/td>\n		\n
    \n
  1. Symmetrical rings: Deviation of a two-point size of inner ring width from its nominal size<\/span><\/li>\n
  2. Asymmetrical rings, upper limit: Deviation of a minimum circumscribed size of inner ring width, between two opposite lines, in any lo<\/em>ngitudinal section which includes the inner ring bore axis, from its nominal size<\/span><\/li>\n
  3. Asymmetrical rings, lower limit: Deviation of a two-point size of inner ring width from its nominal size<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
VBs<\/strong><\/td>\n\n
    \n
  1. Symmetrical rings: Range of two-point sizes of inner ring width<\/span><\/li>\n
  2. Asymmetrical rings: Range of minimum circumscribed sizes of inner ring width, between two opposite lines, obtained from any lo<\/em>ngitudinal section which includes the inner ring bore axis<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
Kia<\/strong><\/td>\nCircular radial run-out of inner ring bore surface of assembled bearing with respect to datum, i.e. axis, established from the outer ring outside surface<\/td>\n<\/tr>\n
Sd<\/strong><\/td>\nCircular axial run-out of inner ring face with respect to datum, i.e. axis, established from the inner ring bore surface<\/td>\n<\/tr>\n
Sia<\/strong><\/td>\nCircular axial run-out of inner ring face of assembled bearing with respect to datum, i.e. axis, established from the outer ring outside surface
\n\n<\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n
<\/td>\nRadial bearings inner ring – tapered bore o<\/em>nly
\n
<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
d1<\/sub><\/strong><\/td>\nNominal bore diameter at the theoretical large end of a tapered bore<\/td>\n<\/tr>\n
\u0394d1mp<\/strong><\/td>\nDeviation of a mid-range size (out of two-point sizes) of bore diameter at the theoretical large end from its nominal size<\/td>\n<\/tr>\n
SL<\/strong><\/td>\nTaper slope, the difference between nominal diameters at the theoretical large end and small end of a tapered bore (d1<\/sub> – d)<\/td>\n<\/tr>\n
\u0394SL<\/strong><\/td>\nDeviation of taper slope of a tapered inner ring bore from its nominal size<\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n
<\/td>\nRadial bearings outer ring<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
D<\/strong><\/td>\nNominal outside diameter<\/td>\n<\/tr>\n
\u0394Dmp<\/strong><\/td>\nDeviation of a mid-range size (out of two-point sizes) of outside diameter in any cross section from its nominal size<\/td>\n<\/tr>\n
\u0394Ds<\/strong><\/td>\nDeviation of a two-point size of outside diameter from its nominal size<\/td>\n<\/tr>\n
VDsp<\/strong><\/td>\nRange of two-point sizes of outside diameter in any cross section<\/td>\n<\/tr>\n
VDmp<\/strong><\/td>\nRange of mid-range sizes (out of two-point sizes) of outside diameter obtained from any cross section<\/td>\n<\/tr>\n
C<\/strong><\/td>\nNominal outer ring width<\/td>\n<\/tr>\n
\n\u0394Cs<\/strong>
\nNormal,
\n
\nModified1)<\/sup>\n<\/td>\n		\n
    \n
  1. Symmetrical rings: Deviation of a two-point size of outer ring width from its nominal size<\/span><\/li>\n
  2. Asymmetrical rings, upper limit: Deviation of a minimum circumscribed size of outer ring width, between two opposite lines, in any lo<\/em>ngitudinal section which includes the outer ring outside surface axis, from its nominal size<\/span><\/li>\n
  3. Asymmetrical rings, lower limit: Deviation of a two-point size of outer ring width from its nominal size<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
VCs<\/strong><\/td>\n\n
    \n
  1. Symmetrical rings: Range of two-point sizes of outer ring width<\/span><\/li>\n
  2. Asymmetrical rings: Range of minimum circumscribed sizes of outer ring width, between two opposite lines, obtained from any lo<\/em>ngitudinal section which includes the outer ring outside surface axis<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
Kea<\/strong><\/td>\nCircular radial run-out of outer ring outside surface of assembled bearing with respect to datum, i.e. axis, established from the inner ring bore surface
\n\n<\/td>\n<\/tr>\n
SD<\/strong><\/td>\nPerpendicularity of outer ring outside surface axis with respect to datum established from the outer ring face<\/td>\n<\/tr>\n
Sea<\/strong><\/td>\nCircular axial run-out of outer ring face of assembled bearing with respect to datum, i.e. axis, established from the inner ring bore surface
\n\n<\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n
<\/td>\nChamfer limits<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
rs<\/sub><\/strong><\/td>\nSingle chamfer dimension<\/td>\n<\/tr>\n
rs min<\/sub><\/strong><\/td>\nSmallest single chamfer dimension of rs<\/sub>, r1<\/sub>, r2<\/sub>, r3<\/sub>, r4<\/sub> \u2026<\/td>\n<\/tr>\n
r1<\/sub>, r3<\/sub><\/strong><\/td>\nRadial direction chamfer dimensions<\/td>\n<\/tr>\n
r2<\/sub>, r4<\/sub><\/strong><\/td>\nAxial direction chamfer dimensions<\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n
<\/td>\nThrust bearings shaft washer<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
d<\/strong><\/td>\nNominal bore diameter of shaft washer, single direction bearing<\/td>\n<\/tr>\n
\u0394ds<\/strong><\/td>\nDeviation of a two-point size of shaft washer bore diameter from its nominal size<\/td>\n<\/tr>\n
\u0394dmp<\/strong><\/td>\nDeviation of a mid-range size (out of two-point sizes) of shaft washer bore diameter in any cross section from its nominal size<\/td>\n<\/tr>\n
Vdsp<\/strong><\/td>\nRange of two-point sizes of shaft washer bore diameter in any cross section<\/td>\n<\/tr>\n
d2<\/sub><\/strong><\/td>\nNominal bore diameter of central shaft washer, double direction bearing
\n\n<\/td>\n<\/tr>\n
\u0394d2mp<\/strong><\/td>\nDeviation of a mid-range size (out of two-point sizes) of central shaft washer bore diameter in any cross section from its nominal size<\/td>\n<\/tr>\n
Vd2sp<\/strong><\/td>\nRange of two-point sizes of central shaft washer bore diameter in any cross section<\/td>\n<\/tr>\n
B1s<\/strong><\/td>\nHeight of a shaft washer of a bearing specifically manufactured for paired mounting<\/td>\n<\/tr>\n
\u0394B1s<\/strong><\/td>\nFor bearings specifically manufactured for paired mounting:<\/p>\n
    \n
  1. Upper limit: Deviation of a minimum circumscribed size of shaft washer height, between two opposite lines, in any lo<\/em>ngitudinal section which includes the shaft washer bore axis, from its nominal size<\/span><\/li>\n
  2. Lower limit: Deviation of a two-point size of shaft washer height from its nominal size<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
Si
\n
<\/strong><\/td>\n		\n
    \n
  1. Range of two-point sizes of thickness between shaft washer raceway and the back face, cylindrical roller thrust bearing<\/span><\/li>\n
  2. Range of minimum spherical sizes between the raceway and the opposite back face of the shaft washer, obtained from any lo<\/em>ngitudinal section which includes the shaft washer bore axis, thrust ball bearing
    \n
    <\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n
<\/td>\nThrust bearings housing washer
\n
<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
\nD<\/strong>\n<\/td>\nNominal outside diameter of housing washer<\/td>\n<\/tr>\n
\u0394Ds<\/strong><\/td>\nDeviation of a two-point size of housing washer outside diameter from its nominal size<\/td>\n<\/tr>\n
\u0394Dmp<\/strong><\/td>\nDeviation of a mid-range size (out of two-point sizes) of housing washer outside diameter in any cross section from its nominal size<\/td>\n<\/tr>\n
VDsp<\/strong><\/td>\nRange of two-point sizes of housing washer outside diameter in any cross section<\/td>\n<\/tr>\n
C1s<\/strong><\/td>\nHeight of a housing washer of a bearing specifically manufactured for paired mounting<\/td>\n<\/tr>\n
\u0394C1s<\/strong><\/td>\nFor bearings specifically manufactured for paired mounting:<\/p>\n
    \n
  1. Upper limit: Deviation of a minimum circumscribed size of housing washer height, between two opposite lines, in any lo<\/em>ngitudinal section which includes the housing washer outside surface axis, from its nominal size<\/span><\/li>\n
  2. Lower limit: Deviation of a two-point size of housing washer height from its nominal size<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
Se
\n
<\/strong><\/td>\n		\n
    \n
  1. Range of two-point sizes of thickness between housing washer raceway and the back face, cylindrical roller thrust bearing<\/span><\/li>\n
  2. Range of minimum spherical sizes between the raceway and the opposite back face of the housing washer, obtained from any lo<\/em>ngitudinal section which includes the housing washer outside surface axis, thrust ball bearing<\/span><\/li>\n<\/ol>\n<\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n
<\/td>\nThrust bearings assembled bearing height<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
T<\/strong><\/td>\nNominal assembled bearing height, single direction thrust bearing<\/td>\n<\/tr>\n
\u0394Ts<\/strong><\/td>\nDeviation of minimum circumscribed size of assembled bearing height from its nominal size, single direction thrust bearing<\/td>\n<\/tr>\n
T1<\/sub><\/strong><\/td>\nNominal assembled bearing height, double direction thrust bearing<\/td>\n<\/tr>\n
\u0394T1s<\/strong><\/td>\nDeviation of minimum circumscribed size of assembled bearing height from its nominal size, double direction thrust bearing<\/td>\n<\/tr>\n
\n2C<\/strong>\n<\/td>\nTotal nominal height of outer rings of assembled bearing, double direction thrust bearing<\/td>\n<\/tr>\n
H<\/strong><\/td>\nNominal assembled bearing height, axial-radial cylindrical roller bearing<\/td>\n<\/tr>\n
\u0394Hs<\/strong><\/td>\nDeviation of minimum circumscribed size of assembled bearing height from its nominal size, axial-radial cylindrical roller bearing<\/td>\n<\/tr>\n
H1<\/strong><\/td>\nNominal assembled bearing sub-assembly height, axial-radial cylindrical roller bearing<\/td>\n<\/tr>\n
\u0394H1s<\/strong><\/td>\nDeviation of minimum circumscribed size of assembled bearing sub-assembly height from its nominal size, axial-radial cylindrical roller bearing<\/td>\n<\/tr>\n<\/tbody>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n
<\/td>\nCartridge units<\/strong><\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
\u0394D2s<\/strong><\/strong><\/td>\nDeviation of a two-point size of cartridge housing seat diameter from its nominal size<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
    \n
  1. \n1)<\/strong>
    \n\t\t\t\t\t\tModified applies to inner rings and outer rings of bearings of matched bearing sets co<\/em>nsisting of two or more bearings and universally matchable angular co<\/em>ntact ball bearings.<\/span>\n<\/li>\n<\/ol>\n","protected":false},"excerpt":{"rendered":"

    TolerancesymbolDefinitionRadial bearings inner ring – cylindrical and tapered boredCylindrical bore: Nominal bore diameterTapered bore: Nominal bore diameter at the theoretical small end\u0394dmpCylindrical bore: Deviation of a mid-range size (out of two<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[2],"tags":[],"class_list":["post-131","post","type-post","status-publish","format-standard","hentry","category-technical"],"yoast_head":"\nTolerance symbols - Loyal Bearings<\/title>\n<meta name=\"description\" content=\"TolerancesymbolDefinitionRadial bearings inner ring - cylindrical and tapered boredCylindrical bore: Nominal bore diameterTapered bore: Nominal bore diameter at the theoretical small end\u0394dmpCylindrical bore: Deviation of a mid-range size\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Tolerance symbols\" \/>\n<meta property=\"og:description\" content=\"TolerancesymbolDefinitionRadial bearings inner ring - cylindrical and tapered boredCylindrical bore: Nominal bore diameterTapered bore: Nominal bore diameter at the theoretical small end\u0394dmpCylindrical bore: Deviation of a mid-range size\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html\" \/>\n<meta property=\"og:site_name\" content=\"Loyal Bearings\" \/>\n<meta property=\"article:published_time\" content=\"2024-07-12T06:23:18+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2024-07-15T07:18:30+00:00\" \/>\n<meta name=\"author\" content=\"admin\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"admin\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"6 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html\",\"url\":\"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html\",\"name\":\"Tolerance symbols - Loyal Bearings\",\"isPartOf\":{\"@id\":\"https:\/\/www.loyal.sg\/article\/#website\"},\"datePublished\":\"2024-07-12T06:23:18+00:00\",\"dateModified\":\"2024-07-15T07:18:30+00:00\",\"author\":{\"@id\":\"https:\/\/www.loyal.sg\/article\/#\/schema\/person\/110a466a1ad2b1a34e532e60b8a9ced2\"},\"description\":\"TolerancesymbolDefinitionRadial bearings inner ring - cylindrical and tapered boredCylindrical bore: Nominal bore diameterTapered bore: Nominal bore diameter at the theoretical small end\u0394dmpCylindrical bore: Deviation of a mid-range size\",\"breadcrumb\":{\"@id\":\"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/www.loyal.sg\/article\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Technical\",\"item\":\"https:\/\/www.loyal.sg\/article\/technical\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Tolerance symbols\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.loyal.sg\/article\/#website\",\"url\":\"https:\/\/www.loyal.sg\/article\/\",\"name\":\"Loyal Bearings\",\"description\":\"\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/www.loyal.sg\/article\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.loyal.sg\/article\/#\/schema\/person\/110a466a1ad2b1a34e532e60b8a9ced2\",\"name\":\"admin\",\"sameAs\":[\"https:\/\/www.loyal.sg\/blog\"],\"url\":\"https:\/\/www.loyal.sg\/article\/author\/admin\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Tolerance symbols - Loyal Bearings","description":"TolerancesymbolDefinitionRadial bearings inner ring - cylindrical and tapered boredCylindrical bore: Nominal bore diameterTapered bore: Nominal bore diameter at the theoretical small end\u0394dmpCylindrical bore: Deviation of a mid-range size","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html","og_locale":"en_US","og_type":"article","og_title":"Tolerance symbols","og_description":"TolerancesymbolDefinitionRadial bearings inner ring - cylindrical and tapered boredCylindrical bore: Nominal bore diameterTapered bore: Nominal bore diameter at the theoretical small end\u0394dmpCylindrical bore: Deviation of a mid-range size","og_url":"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html","og_site_name":"Loyal Bearings","article_published_time":"2024-07-12T06:23:18+00:00","article_modified_time":"2024-07-15T07:18:30+00:00","author":"admin","twitter_card":"summary_large_image","twitter_misc":{"Written by":"admin","Est. reading time":"6 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"WebPage","@id":"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html","url":"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html","name":"Tolerance symbols - Loyal Bearings","isPartOf":{"@id":"https:\/\/www.loyal.sg\/article\/#website"},"datePublished":"2024-07-12T06:23:18+00:00","dateModified":"2024-07-15T07:18:30+00:00","author":{"@id":"https:\/\/www.loyal.sg\/article\/#\/schema\/person\/110a466a1ad2b1a34e532e60b8a9ced2"},"description":"TolerancesymbolDefinitionRadial bearings inner ring - cylindrical and tapered boredCylindrical bore: Nominal bore diameterTapered bore: Nominal bore diameter at the theoretical small end\u0394dmpCylindrical bore: Deviation of a mid-range size","breadcrumb":{"@id":"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/www.loyal.sg\/article\/s92\/tolerance-symbols.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.loyal.sg\/article"},{"@type":"ListItem","position":2,"name":"Technical","item":"https:\/\/www.loyal.sg\/article\/technical"},{"@type":"ListItem","position":3,"name":"Tolerance symbols"}]},{"@type":"WebSite","@id":"https:\/\/www.loyal.sg\/article\/#website","url":"https:\/\/www.loyal.sg\/article\/","name":"Loyal Bearings","description":"","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.loyal.sg\/article\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"Person","@id":"https:\/\/www.loyal.sg\/article\/#\/schema\/person\/110a466a1ad2b1a34e532e60b8a9ced2","name":"admin","sameAs":["https:\/\/www.loyal.sg\/blog"],"url":"https:\/\/www.loyal.sg\/article\/author\/admin"}]}},"_links":{"self":[{"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/posts\/131","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/comments?post=131"}],"version-history":[{"count":1,"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/posts\/131\/revisions"}],"predecessor-version":[{"id":704,"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/posts\/131\/revisions\/704"}],"wp:attachment":[{"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/media?parent=131"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/categories?post=131"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.loyal.sg\/article\/wp-json\/wp\/v2\/tags?post=131"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}